Armored Basilisk Conversion

My apologies for not posting in a while. After getting caught up from the holidays, I found I was getting frustrated with my paint pot procrastinating. As busy as I stay with building and converting, and even getting a start to the painting, I still run into a painters block and can't seem to get things finished. Rather than post unfinished stuff, I held off in hopes I'd finish and be able to post a complete project. So far, no good. I've decided to post my WIP here, in hope that you all will forgive my painters block for a while.

First up is my Armored Basilisk Conversion. You might remember my post a while back about double tracking the new Hellhound hull. I had noted I was working on something I'd show later. This is the something. In the top picture you can see I used a Shadowsword turret assembly as the basis for an armored Basilisk. The turret is too wide to fit the standard Chimera hull, so some modification was needed to make it work. The picture to the right is the WIP for the double tracking of the hull I discussed in a previous post. The old Chimera sides made it too wide, so I used the new Chimera sides. It actually works quite well.

The next challenge was to make the barrel assembly. I didn't want to just plop a Shadowsword top on a widened Chimera hull. Plus I was getting the big parts from bitz buys and wanted to limit my purchases. So I scratch-built the barrel using a writing pen tube, an Xacto blade protector, and barrel bits from an old style Demolisher. I found a large plastic bushing to transition from barrel to turret. A nail holds it in place, allowing the barrel to elevate. The turret doesn't rotate, which begs the question, “Is it still a turret?” My original barrel-to-hull transition was cumbersome, and would have complicated making the turret rotate, so I decided not to try. I wished I’d rethought when I change to the bushing, because I think making it rotatable, like modern self propelled artillery, wouldn’t have been that much more effort. If I can get the bitz cheap, I may try it.

As you can see, there's a fair amount of card stock involved. I've had plain plastic stock saved up for a while, but I didn't hesitate to use other stock of opportunity. In this picture, you can see a used gift card. The blue pieces are punch-outs from an electrical circuit box and are supposed to be vents. The clear pieces were once a twist off top to a drink bottle, and will be tail/backup lights and perhaps a place to add some markings. I broke one of the antennas off before I was even done with it, and both are now magnetized.


Two more pictures to show the front and other side. While the intent was to magnetized the hull weapon, instead of adding a magnet I glued a piece of metal under the hole. I figured the magnet would be strong enough, but now I miss the holding power of using two. For instance, I’m not sure where the HB I magnetized, missing in these latest pics, has gone. Yep, magnet on both sides from now on…

Basilisk: More WIP

Amongst the four models on my work bench now (not counting various infantry in the paint pot queue), is this standard Basilisk. I posted a WIP a few weeks ago. After two tone painting a few Leman Russ tanks, I've decided my standard paint scheme needed a small bit of light grey. The main two colors on my vehicles are a gray spray primer and a camo tan Krylon paint for plastics. Since this Basilisk was the first planned from the outset as three colors, I decided to start with a light grey base coat. I then taped the areas needing to remain light grey, and followed with a coat of dark grey. Another taping (over the original), and follow up with the final coat of camo tan.

While I like how it turned out, I found I tend toward applying heavy coats of spray. I guess I wanted to be sure I got a solid, even coat all around, but this can lead to some thick areas where the third coat is applied. Some of the tape lines needed smoothing as well. Frankly it probably isn't much different than I'd have achieved brushing it on, so I'm not concerned about this particular piece. I will however take a lighter touch on the next try.

I am also considering applying the light grey last. The light grey overlaps the other two colors, so that would require removing the previous tape and reapplying for the final coat. Something I had hoped to avoid by spraying light grey first, but I think applying it last would thin the paint over most of the model.

As you can tell from my earlier post about it, this Basilisk is the victim of my Paint Pot Procrastination because of another distraction on the workbench, a Valkyrie. I couldn't resist detailing the inside, and have probably put more time into it than I will the outside. A shame considering the outside will be seen much more than the inside, but I really enjoy the detail GW put into it and wanted to do it up nice. One thing I relearned here is the sticking power of primer over straight paint. To be sure of a strong bond where the hull pieces will attache, I removed the grey primer along the edges. It took a bit of scraping to get it all. Scraping regular paint from plastic means big chunks at a time. Paint over primer is much more stubborn. Really hit home the need to prime first.

Basilisk WIP

So, I purchased a Basilisk on eBay a while back. I had always had good luck with my eBay purchases. That was not the case here. It was pretty bad off. Most of the back end and some gun carriage parts were broken or missing, and there was glue in too many places. I now buy only un, or partly, finished stuff. The sides were still salvageable, as was the gun itself. Shortly after this purchase, I was lucky to get a couple more Basilisks still on the sprue for a steal. Unfortunately, they mostly sat waiting for their time to be built. I was inspired recently to build an armored Basilisk; now still very much WIP, to be covered soon. Many of the parts I won't be needing on the armored variant are exactly what I needed to flip the ruined piece. Here is the WIP.


This is pretty much the standard Basilisk. I don't like the tall shield, so cut that down a bit. It's got some old pewter pieces thrown in, and I've still got some little adjusting to do, but it's pretty much done. I did try a little something different with the back. I added some window screen to fill in the gap between floor and hand rail. Last thing the crew wants is a wayward round rolling off the back. Plus, it's a great place to hang their packs and other assorted gear. Note the backpack in the lower left will be hanging off one of the side hand rails after it's all painted.

One thing I've been concerned with for my own Basilisks was the ladder on the back end. It's a very breakable piece, just hanging out the back by two fragile pieces of plastic. Even a Forge World example shows this break point (see bottom picture here). So, I gave it a bit of thought and came up with an idea for a "hinge." I drilled a hole through one of the round bits you find on the back of every sprue, sliced pieces of the round, trimmed a flat end and glued it to where the ladder usually connects, where the rivets are. I trimmed, rounded and holed each top of the ladder, and connected it all together with the head of a pin. Now I can flip it over to a somewhat safer area for transit. I had hoped it would lay over flat, but I didn't get it trimmed right. I didn't want to adjust this one anymore, as that would just weaken the remaining plastic. I still think it's possible to get it to lay flat, and will give it another go when I finally get around to building my other standard Basilisk.